 |
 Maintenance
Parts List
Product Guarantee
Mr. Good Pedal
|
 |
Can replacement handgrips be purchased for my trike? - Back to Top
Yes, the handgrips can easily be replaced. Measure the diameter of the handle bar tubing. It will either measure ¾" OR 1".
For 3/4" tubing, you will need FS012R
For 1" tubing, you will need FS009R
Can I purchase replacement pedals for my trike? - Back to Top
Yes, all Angeles trikes have a 7/16" pedal crank and the pedals slide onto the crank and are held in place by a pal nut. You will need to order:
For red pedals the part number is PL412 and you will need a FS050 pal nut for EACH pedal
For black pedals the part number is PL412B and you will need a FS050 pal nut for each pedal.
Is it possible to replace the entire front wheel with crank? - Back to Top
Yes you can, but if you aren't sure of the wheel size, you will need to measure the front wheel from the outer rubber edge to the opposite side outer rubber edge. It will measure close to 10", 12" OR 14". If the tire is very worn, the measurement could be less than these dimensions.
For a 10" Front Wheel With Crank, order part PW333R
For a 12" Front Wheel With Crank, order part PW335R
For a 14" Front Wheel With Crank, order part PW336R
Is there a complete front wheel assembly available to buy? - Back to Top
Yes. This assembly will include the wheel with crank and all hardware out to the pedal and pal nut.
If you aren't sure what size wheel you will need to measure the front wheel from the outer rubber edge to the opposite side outer rubber edge. It will measure close to 10", 12" or 14". If the tire is very worn, the measurement could be something less than these dimensions.
We also will need to measure the tubing of your trike. If it measures ¾" you will need to order:
For a 10" Front Wheel and ¾" tubing order Part WP337R
For a 12" Front Wheel and ¾" tubing order Part WP338R
For a 14" Front Wheel and ¾" rubbing order Part WP339R
If the tubing measures 1" you will need to order:
For a 10" Front Wheel and 1" tubing order Part WP337SR
For a 12" Front Wheel and 1" tubing order Part WP338SR
For a 14" Front Wheel and 1" tubing order Part WP339SR
Is it possible to purchase replacement back wheels for my trike? - Back to Top
Yes. The majority of all Angeles trikes require 8" back wheels.
Order part PW 375RH.
If you do not have the hardware to secure the wheel to the axle, you will need to order:
Locknut FS081 and Bolt FS198B.
Is it possible to purchase replacement seats for my trike? - Back to Top
Yes. If your seat is a flat seat you will need to order:
Part PL426R and two FS049D bolts and two FS086 nuts
If your seat is a bucket seat with a high back you will need to order:
Part PL47R and two FS049 bolts and two FS085 nuts
Is it possible to purchase just a replacement fork (handlebar) for my trike? - Back to Top
Yes. To determine the size fork (handlebar) needed, you must first determine the size of the trike you have.
The size of your trike is determined by the size of the front wheel. Additionally, you will need to measure the tubing of your trike. If it measures ¾", you will need additional parts.
*If you have the Supercycle Trike (low rider) note that the fork is a different style than the upright trike forks.
Measure the front wheel from the outer rubber edge to the opposite side outer rubber edge. It will measure close to 10", 12" or 14". If the tire is very worn, the measurement could be something less than these dimensions. After determining the front wheel size of your trike, you can order the following for a Fork with 1" Tubing:
A fork (handlebar) for a trike with 10" Front Wheel order Part PP450, two hand grips Part FS009R, and two nylon bearings PL419
A fork (handlebar) for a trike with 12"/14" Front Wheel order Part PP452 two hand grips Part FS009R, and two nylon bearings PL 419
A supercycle fork Part PP454, two hand grips FS009R and two PL419 nylon bearings
Fork with ¾" Tubing will be Replaced with a Fork with 1" Tubing
A 1" fork (handlebar) for a trike with 10" Front Wheel order Part PP450, two PL419 nylon bearings and two hand grips Part FS009R
A 1" fork (handlebar) for a trike with 12"/14" Front Wheel order Part PP452, two PL 419 nylon bearings and two hand grips FS009R
A supercycle fork Part PP454, two PL 419 nylon bearings and two hand grips FS009R
Is it possible to purchase just a replacement frame for my trike? - Back to Top
Yes but in order to do that I will need to know what trike you have.
To determine if you have a 10", 12", 14" or Supercycle Trike, measure the front wheel from the outer rubber edge to the opposite side outer rubber edge. It will measure close to 10", 12" or 14". If the tire is very worn, the measurement could be something less than these dimensions.
A frame for a trike with 10" Front Wheel order Part PP457
A frame for a trike with 12" Front Wheel order Part PP458
A frame for a trike with 14" Front Wheel order Part PP459
A frame for the Supercycle with 14" Front Wheel order Part PP461
A frame for a Carry-All with 12" Front Wheel order Part PP208
A frame for a Rickshaw with 12" Front Wheel order Part PP467
A frame for a Tandem Trike (School Bus & Police) with 12" Front Wheel order Part PP469
A frame for a Cargo (Fire Truck) with 12" Front Wheel order Part PP468
What if a "Bye-Bye" Buggy needs a replacement brake? - Back to Top
It is helpful to know the year the "Bye-Bye" Buggy was purchased. The following is a historical list of brake systems used on Angeles buggies:
Green/red foot lever - no longer available
Bicycle handgrips - limited supply of replacement parts are available.
Suggest customer check with a bicycle shop for replacement parts such as cable or brake pads
Lawnmower-type handle - no longer available. Suggest customer check with a bicycle shop for replacement brake pads.
Foot brakes for buggies manufactured from 2005 to present. A new back wheel with brake would be sent to the customer. The buggy is guaranteed for 3 years from purchase. If buggy is still under warranty, the wheel will be sent at NO CHARGE.
I need to replace the seat belts on my "Bye-Bye" Buggy. Can I order replacement seat belts? - Back to Top
It is helpful to know the year the "Bye-Bye" Buggy was purchased. If you do not know the year, below are few questions to help determine when your buggy was manufactured:
Does the buggy have white bucket-type seats? If so, your buggy was manufactured prior to 1993 - The seat belt is considered "old" style and the part number is PL 279.
Does the buggy have red and white seat pads that slip over the headrest? If so your buggy was manufactured after 1993. The seat belt is considered "new" style, and the part number is PL278.
Can I buy replacement seat belts for the buggy infant seat? - Back to Top>
Yes. The item is PL280B. Replacement seat belts are in stock.
|
|
Can I buy replacement wheels for my "Bye-Bye" Buggies? - Back to Top
It is helpful to know the year the "Bye-Bye" Buggy was purchased. If you do not know the year, below are few questions to help determine when your buggy was manufactured:
Manufactured prior to 1993
Does the buggy have white bucket - type seats? If so, your buggy was manufactured prior to 1993.
If you have a 4 passenger buggy the front wheels are 5" on the front of your buggy. The 5" wheels are no longer available.
If you have a 6 passenger buggy the front wheels are 12" and the rear wheels are 16". Both wheels are still available.
Manufactured after 1993
If your 4 passenger buggy was manufactured after 1993, the front wheels are 8": and the rear wheels are 12". Both wheels are available.
If your 6 passenger buggy was manufactured after 1993, the front wheels are 12" and the rear wheels are 16". Both are available.
Manufactured after 2005 or later
If your buggy was manufactured 2005 or later (identified by a foot brake) does your buggy have thin wheels or fat wheels?
If your buggy has thin wheels, I need to ask you some questions regarding the wheels. Please look at your wheels and tell me if the wheels are "recessed" or "symmetrical".
"Recessed" Wheel - The lock nut on a recessed wheel will rest inside of the metal hub.
"Symmetrical" Wheel - The lock nut on a symmetrical wheel will rest on top of the metal hub.
Both wheels are available for replacement and are replaceable at NO CHARGE for 3 years from purchase.
Can I purchase canopies for my buggy and how do I determine which canopy to buy? - Back to Top
Please look at your buggy to determine if you have receptacles for a two-pole canopy or a one-pole canopy.
If you see one rectangular well between the seats (each row), you will need a one pole canopy FB6500A for each row of seats.
If you see two round receptacles with white PVC piping on each side of the row of seats, you will need the 2 pole canopy FB6500 for each row of seats.
|
|
|
